filename: TFS115K.doc version 2.2 04.12.2012 vectron international filter specification tfs 115k 1/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. measurement condition ambient temperature: 23 c input power level: 0 dbm terminating impedance: * input: 1076,00 || - 11,82 pf output: 1049,50 || - 10,82 pf characteristics remark: the reference level for the relative attenuation a rel of the TFS115K is the minimum of the pass band att enuation. this value is defined as the insertion lo ss a e . the nominal frequency f n is fixed at 115,2 mhz without any tolerance. the v alues of relative attenuation a rel are guaranteed for the whole operating temperature range. the frequency shift of the filte r in the operating temperature range is included in the production tolerance scheme. d a t a typ. value tolerance / limit insertion loss **** a e 5,6 max. 8,5 db (reference level) nominal frequency f n - 115,2 mhz passband pb - f n 0,1 mhz pass band ripple (pk-pk) 0,5 max. 1 db pass band ripple f n 0,025 (pk-pk) 0,01 max. 0,10 db pass band ripple f n 0,025... f n 0,05 (pk-pk) 0,07 max. 0,15 db bandwidth *** 1 db 0,26 mhz min. 0,2 mhz 20 db 0,67 mhz max. 0,8 mhz relative attenuation a rel f n ... f n 0,1 mhz 0,5 max. 1 db f n 0,4 mhz ... f n 0,8 mhz 25 min. 20 db f n 0,8 mhz ... f n 5,0 mhz 29 min. 25 db f n 5,0 mhz ... f n 10,0 mhz 53 min. 35 db f n 10,0 mhz ... f n 15,0 mhz 61 min. 45 db f n 15,0 mhz ... f n 25,0 mhz 67 min. 50 db average group delay within pb 1,92 max. 2,4 s group delay ripple within pb pk-pk 361 max. 600 ns return loss within pb 13,7 min. 10 db oip3 ***** 35 min. 30 dbm input power level - max. 15 dbm operating temperature range otr - - 30 c ... + 75 c storage temperature range - - 30 c ... + 75 c temp erature coefficient of frequency tc f ** -0,036 ppm/k - *) the terminating impedances depend on parasites a nd q-values of matching elements and the board used , and are to be understood as reference values only. should there be additional questions do not h esitate to ask for an application note or contact o ur design team. **) ? f(hz) = tc f (ppm/k 2 ) x (t-t 0 ) 2 x f cat (mhz). ***) measured at ambient temperature. ****) 7db max at ambient temperature (using our tes t fixture). *****) f in1 = 115,185 mhz; f in2 = 115,215 mhz; f measurement1 = 115,155 mhz; f measurement2 = 115,245 mhz; p in = 0 dbm generated: checked / approved:
filename: TFS115K.doc version 2.2 04.12.2012 vectron international filter specification tfs 115k 2/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. 114.9 114.96 115.02 115.08 115.14 115.2 115.26 115.32 115.38 115.44 115.5 -5 -4.5 -4 -3.5 -3 -2.5 -2 -1.5 -1 -0.5 0 frequency in mhz magnitude in db 114.9 114.96 115.02 115.08 115.14 115.2 115.26 115.32 115.38 115.44 115.5 1.2 1.74 2.28 2.82 3.36 3.9 4.44 4.98 5.52 6.06 6.6 frequency in mhz delay in s -40 -20 0 20 40 60 80 -6.6 -6.4 -6.2 -6 -5.8 -5.6 -5.4 -5.2 temp(c) insertion loss (db) TFS115K - insertion loss over temperature 90.9 95.76 100.62 105.48 110.34 115.2 120.06 124.92 129.78 134.64 139.5 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 frequency in mhz magnitude in db insertion loss: -5.63 db filter characteristic construction and pin connection (all dimensions in mm) 13,6max. 6,8max. 1 2,0max. 8 9 10 1,5 2,54 0,15 2,54 0,15 0,8 0,1 1 2 3 4 56 7 11 12 date code 50 test circuit tfs 115k a18 1 ground 2 ground 3 ground 4 ground 5 output 6 output rf return 7 ground 8 ground 9 ground 10 ground 11 input 12 input rf return date code: year + week a 2010 b 2011 c 2012 ... c1 l1 saw l2 c2 11 5 1, 2, 3, 4, 7, 8, 9, 10 6 12
filename: TFS115K.doc version 2.2 04.12.2012 vectron international filter specification tfs 115k 3/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. stability characteristics, reliability after the following tests the filter shall meet the whole specification: 1. shock: 500g, 1 ms, half sine wave, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0,35 mm or 5 g respe ctively, 1 octave per min, 10 cycles per plane, 3 p lanes; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 30 min. each / 1 0 cycles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " air reflow temperature conditions" on page 4; this filter is rohs compliant (2002/95/eg, 2005/618 /eg) packing tape & reel: iec 286 ? 3, with exception of value f or n and minimum bending radius; tape type ii, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 1700 reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm g do w ct f e g d1 p2 p1 po bo ao pull off direction pin marker typ date code ko t a c n w 1 w 2 the minimum bending radius is 45 mm. tape (all dimensions in mm) w : 24,00 +0,30/-0,10 po : 4,00 0,1 do : 1,50 +0,1/0 e : 1,75 0,10 f : 11,50 0,10 g(min) : 0,60 p2 : 2,00 0,1 p1 : 12,00 0,1 d1(min) : 1,50 ao : 7,10 0,10 bo : 13,90 0,10 ct : 21,5 0,1 reel (all dimensions in mm) a : 330 w1 : 24,4 +2/-0 w2(max) : 30,4 n(min) : 60 c : 13,0 +0,5/-0,2
filename: TFS115K.doc version 2.2 04.12.2012 vectron international filter specification tfs 115k 4/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. air reflow temperature conditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/ second > 100c between 300 and 600 seconds > 150c between 240 and 500 seconds > 217c between 30 and 150 seconds peak temperature max. 260c time within 5c of actual peak temperature between 10 and 30 seconds cool-down rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds temperature / c time / s max. 260c 217c 10 ... 30 s 30 ... 150 s max. 300 s chip-mount air reflow profile
filename: TFS115K.doc version 2.2 04.12.2012 vectron international filter specification tfs 115k 5/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. history version reason of changes name date 1.0 - generation of development specification hodkin 24.05.2010 1.1 - bandwidth adjusted to 200khz hodkin 25.05.2010 1.2 - narrower typical bw & now fc definition. jaffer 25.05.2010 - changed input power level & average group delay w ithin pb. - included typical values from simulation for custo mer discussion. 1.3 - introduced amplitude ripple over 50 &100khz r anges, ip3 included. jaffer 25.05.2010 2.0 - converted to fn definition. jaffer 05.11.2010 2.1 - add plots, typ values from measurements (of 1 1/3/11) filter specification. jaffer 15.03.2011 2.2 - add typ values for ip3 (our measurements are based on oip3) jaffer 04.12.2012
|
